Thread: Gigabyte Extreme X58

Hello I have been seeing many of you have this motherboard, and like I have problems or are giving problems with the bios which is very green, then went on to explain what they must do to achieve stability in this motherboard, I hope it is helpful:

Machine data for these values of Evidence:
CPU: Core i7 920 2.67 GHz @ 3200Mhz Default.
Motherboard: Gigabyte X58 Extreme.
RAM: A-Data G Series 3x2GB 9-9-9-24. (1600Mhz)

1 Download the latest BIOS (Updated):

2nd low and put the bios desconprimida in the root of a usb memory.

3 enter the bios as we all know pressing the Delete key

Option 4 Wanted puts Update:
Press F8 Q-Flash

5th save ours doing a backup and then we start to update the bios, once complete reboot the pc,

6 Once you restart press the Tab key and press Pause to see if the version we F5 to update the BIOS, you must put:

EX58-EXTREME F5

We continue to enter to the load

press the Delete key and enter the Bios, and now put the following:

1 Click the first option in the BIOS (MB Intelligent Teak (MII)

Within this menu to configure Asín:

Cpu Clock 20x

Here two options:

1 Option BCLK Frequency (MHz) 160 (Micro to 3200mhz)

ó

2nd Option BCLK Frequency (MHz) 133 (a 2.666mhz Micro)


Enhance Performance (Standard)

System Memory Multiplier (SPD) = 10.0 (Option 1)
(Ram Micro to 3200Mhz)

ó

System Memory Multiplier (SPD) = 12.0 (2nd Option)
(Ram Micro to 2666Mhz)



* Note BCLK = SPD x = 1600 MHZ.

* Note Latency = put in Manual and implement the values that
bring the memories recorded in the sink of them, eg in my case:

* Annotation sink in the report:
Cas Latency Timing: 9-9-9-24

Asin is:

Channel A
Cas Latency time --- 9
TRCD ----------- 9
TRP -------------- 9
THERE ------------ 24
COMMMAND RATE (CMD) Order

Channel B
Cas Latency time --- 9
TRCD ----------- 9
TRP -------------- 9
THERE ------------ 24
COMMMAND RATE (CMD) Order

Channel C
Cas Latency time --- 9
TRCD ----------- 9
TRP -------------- 9
THERE ------------ 24
COMMMAND RATE (CMD) Order



Remain below and find the Voltage leave it like this:

Load-Line Calibration (Enabled)

Cpu Voltage = 1.12500V (Option 1, a Micro 3200Mhz)

ó

Cpu Voltage = 1.11875V (Option 2, Micro to 2666Mhz)




QPI / Ult Voltage = 1215V (Option 1, a Micro 3200Mhz)

ó

QPI / Ult Voltage = 1195V (Option 2, Micro to 2666Mhz)

QPI / Voltage Ult = (This value is responsible for the headache he has given us over to a vat where it will boot off the motherboard and instantly became a single turn)

and the section of Memory Voltage applied to our working memories, eg

* Annotation sink in the report:
Working Voltage: 1.65V ~ 1.85v

DRAM Voltage 1.58V (same for Option 3200Mhz or 2666Mhz)

1.58 V apply in this instance, I work well even if Voltage
a bit lower it says the manufacturer, (Out Voltage - heat)

Once all this again with the cursor a little above the Bios and do the following:

2nd Visit (CPU Advanced Features)

There will be several options, such as leaves then disable:

INTEL (IE) TURBO BOOST TEAM (DISABLE)


C3/C6/C7 STATE SUPPORT (DISABLE)
ENHANCED HALT CPU (DISABLE)
CPU THERMAL MONITOR (DISABLE)
CPU EIST Function (DISABLE)


Once this fact all the above back to the main menu
bios now but to set things in bios, by pressing the Esc key:

Enter now at:

Advanced Bios Features:

Enable this option:
HHD Capacabity SMART (Enabled.)
Uncheck the following:
Full Screen Logo Show (Disable).

Back to ESC.

Now enter this submenu:

Integrated peripherals:

Inside here activates two options that are very useful:

Enabled USB Keyboard Function
Enabled USB Mouse Function

Turning again (ESC)


and we enter the last option we are going to play:

PC Health Status

We configure it as follows;

CPU Warning Temperature: 60 º / 140 º F

CPU FAN FAIL (Enabled)
CPU SMART FAN CONTROL (Enabled)
CPU SMART FAN MODE (Voltage)

* Note: The other options (Disable)



Once this is all good because we get to the ESC to main menu of the Bios,
Now what will AREM Bookmark this custom in our Bios Settings, as follows:
Press the F11 key and then a menu, we name, eg CPU2666MEMO1600 We CPU3200MEMO1600 or to enter and exit the BIOS by pressing F10, if you say you want to exit saving changes (Y) and Enter, and Buale, and everything is configured and stable PC.


I hope you've enjoyed the guide, saludos.

Produced by fersergar ..

you come out a good Micro .. 1.1va just see if this pace keeps you in if you upload more good explanation, and that the difference between V and QPI reports should not exceed 5

if it goes up more, but I am not interested in climbing over the microphone as this is like a shot, going faster than me clicking jaja, esque truth is a real shot, intel has done very good work, greetings.

I made some changes to the configuration of computer for more stability, after making a test of stability I have found that it fell short of information is given and an error voltage, which solves Put now these voltages with this configuration:

Cpu Voltage = 1.12500V

QPI / Ult Voltage = 1.215 V

1.58V DRAM Voltage

Voltage increases have been minimal but again after passing the test, have been more than enough to not have given me back a blue screen if I did before I had the voltages posts, I decided to take the test because sometimes, very occasionally, I went the typical blue screen, and this moment is just the problem, greetings and hope you will help us all.

Here I leave a picture as it should be micro Overclock Without Once we apply all this in the guide that I have mounted the AVC Samurai Black, Copper and Aluminum) (Pasta Termica Seven Carat Diamond (Diamond)) and have cojido temperatures with a CPU usage downloading files, browsing the Internet, desktop, and after several days without shutting down the computer.

How many volts I put the plate esk me leaving many different.

Put it all as he explained, will see some inestablidad system, do some testing micro memory to know what went wrong, testing programs that extrusion component failure raise the voltage a bit, secludes.

I'm good berserker led and emails already solved the problem of the boat due to the PSU that was bad, like I said now I can not install or a single 64-bit operating system, and 32 if lod, lso worse with 64 or finish what typical loading files or maybe half of me always throws a load screen, listen to something more than 4g of memory I had problems getting an x64 but with the xp and 64 ¿?¿?¿, q is the thing with the source of the poor could be 64 and not 32! and now with the sound source to the contrary jajaja this is crazy, well I have 3x2 = 6g Corsair xms3 model TR3X6G1600C9 G 1600 MHz 9-9-9-24 1.65 v, a 3way sli-i7 920 and a plaque is the same as yours but not the extreme if not UD5 normal, any suggestions or help?

thanks and greetings

Hello, would you comment on that program I recommend to check if the pc is stable? esque yesterday without eating or drinking it, and hit the reset is just whack xDD and I am just scratching 1: S is the 1 time I rebooted since I got it, and as fair coincided with the bios update and Tokar to memos of voltages and so on, ah and another thing, I saw the message at the bottom of page 2 in the other post (in 1600 with a plate of OCZ x58) Thank you, greetings!

Forgive, that is a guest post from me, that I forget legwarmer xDDDD

If you have other memories than mine to work like a little more voltage, 1.65 V to upload work that way and try to see that, to see if it stabilizes your computer, if sigiera failing, upload a low voltage, only information is the next step of voltage to the other components that I put in the guide, you can screen it at the time that the team needs more performance, it is short and the screen voltage, test to see that as regards the operating system, though I installed Windows Vista 64bits with triple channel on, the memories I have placed on the banks of the white board, so maybe you have the blue and this is the problem, I think it does not matter to put the memories always respect the colors of the banks, try to see me and comment, greetings.

hello, would you comment on that program I recommend to check if the pc is stable? esque yesterday without eating or drinking it, and hit the reset is just whack xDD and I am just scratching 1: S is the 1 time I rebooted since I got it, and as fair coincided with the bios update and Tokar to memos of voltages and so on, ah and another thing, I saw the message at the bottom of page 2 in the other post (in 1600 with a plate of OCZ x58) Thank you, greetings!

Hey, look at me with estube testing program that brings extresar EVEREST Ultimate Edition, which gives quite a cane components, tested each component separately, the top in the options bar, which puts Tools, and within here where it System Stability Test, marking what they want to do the test and give it to Start, saludos compañero.

Hello, just get in Everest, ye ego key too me say that, in the stress test cpu to 4min, I get blue screen, Key I do now? Key what goes wrong? Thank you very much. un Saluda companion.

Just remove the Intel turbo boost, ego ye again stress the cpu, Everest, and I was not pet ado to 4 min, 15 min I was like, not pet ado, this is the turbo boost to do something ? Another thing, how long is the strip Everest doing the test? eke do I want to test the cache or otherwise, and will not let me, it starts all the time to stress the cpu.

thank you very much, a welcome companion.

pd: if you tell me that some other program to make sure the computer is fine, xke take a week, will give me ke Argo XD

The turbo is what makes overclokear, the more speed is the micro is going to need more voltage, it is easy asin, more like a car running while consuming more, it could equal, if you leave the turbo position and not get a little but since the crash because voltage is not stable with that voltage, I do not have the turbo on, try to raise a little more to the micro vulgate, if given a screen test qpi raise information is, everything is to try as well the ram, but it is almost always a lack of voltage to the micro, expresser this program for the ORTHOS too, greetings, and told me.