Overclocked AMD 2400+

**Adam Hollioake** · 05-06-2009, 11:20 AM

Anyone who does not risk does not cross the River.

This guide will explain how to modify and an overclocked AMD Sempron 2xxxx (in my case is a 2400 +), which is almost a T-Bred B with a higher fsb, and a covert AMD XP Mobile, so the multiplier CPU is unlocked. All this based on my personal experience.

I must confess that I dared to change the cpu pure obsessive, but surely will have many like me, well then that the emotion is great work... you understand me.

Well, let's get to the grain...

The purpose of this guide is an AMD Sempron as they come with the multiplier. Therefore not used the method of wire, and thus becomes very difficult only by FSB. This becomes even more evident because it now has a chipset with msi kt400a, which some will not block as nForce AGP and PCI, and only gets around 180 fsb stable.

**Mike Atherton** · 05-06-2009, 11:23 AM

The CPU is not holding or not ... the multi MHz ... are quite a Vcore as fabrika for example..... I leave it in 15 xs but 166fsb... ... with 2500 MHz Vcore is 2.1 and stable.

That in my old cpu ... but not in this for me....that the stepping is probably not as good as the previous.

The Vcore is high mine by the FDE.... and not much scares me due to I have a good cooling the cpu and the jar etc .. Is not the best but quite good air... I work very stable ... something is important is the temp of the cpu and must be always less than 60 to say the cpu temp is in good my temp around 45 to 56 to 3400rpm the polo735 with 2400mhz with 2.1vcore 1 fan pulling and 2 entering into the jar.

**Alec Stewart** · 05-06-2009, 11:25 AM

No roof is ...... what is going. The Vcore is very important the CPU is asking more than current MHz ... so falls ...... have good temperature.

**Allan Lamb** · 05-06-2009, 11:28 AM

13.5 x 13x fsb......... As I was with these things? I ask 200FSB using the test.

200FSB with 13x that is 2600 MHz with 1.9 vCore.

**Adam Hollioake** · 05-06-2009, 11:31 AM

200, 199, fsb, but I repeat to 13.5 noticing unstable. When you have time to upload core 2, but before I paint the final painting conductors, not exit.

**Graham Gooch** · 05-06-2009, 11:34 AM

Felicitates 2600mhz is good ... and NUNK AHE seen to reach both Prior to this my Sempron reached 2500mhz with 2vcore and with this I can not pass 2460mhz with 2.1vcore.

**Adam Hollioake** · 05-06-2009, 11:36 AM

With a friend we will make a speech to the 2500 Barton normal, you know to come to terms to make sure a little? I think I buy into here.

Greetings

**John Emburey** · 05-06-2009, 11:40 AM

I think if stable until the kt600 Legaria ed over 225fsb but that's not what I tried the climb... and lo maximo best I leave in the Ensim 220fbs ma memos I stand by.. 2700 are forced to 3200.

I'll try a new Sempron 2200 + if I get good aver... this was before the 2.0vcore with achieving the 2500 MHz.

**Mike Gatting** · 05-06-2009, 11:43 AM

I wonder one thing, I have a GA-7vt600RZ with or 2400 + but the plate or bloke, there is a way to raise the FSB without risk? Any modified bios or anything with dividers... is not something.

**Adam Hollioake** · 05-06-2009, 11:47 AM

On the basis that you are working with bus 200 (200 * 10 = 2000 MHz). As if the KT600 comes fsb to 200, making these changes is that divided by 200 gives 33.3 and 6 MHz, which is the bus speed, and is * 2 (66mhz) If you try to climb over the FSB of 200 (say 220) to reach the 36.6 MHz and to 73.3, which is the recommended maximum that may be required at those ports (37 MHz). If you could modify this bios divider, you can raise the FSB to 233MHz and the divisor of 7 and would have no problems with the pc.If the option does not exist, I recommend you not go up from 220 as it would be risky for your devices on the AGP and PCI ports.

Compared to other alternatives bios, I do not know specifically, but would have to investigate.

Greetings

**Norman Gifford** · 05-06-2009, 11:49 AM

It's not really the change the registry holds divider pci and but it is of these changes when we have a board with this possibility Chipsets KT600 your maximum divisor is 1 / 6 achieved only with 200FSB pci 33.3 but more than that ... it goes up, if can be dangerous I recommend not pass 215fsb.

**Adam Hollioake** · 05-06-2009, 11:53 AM

I did the mod a Sempron 2600 +, and I left at 2500 reales (200 * 12.5), with a 10% higher voltage, something like 1.85.

Has stable operation, a heat sink with TR3, and the program extreme, 35 º and 40 º.

Was purchased in SYM

Pretty good I think I paid the same as a mobile for 25 Lukas less.

Greetings

**Ian Botham** · 05-06-2009, 11:57 AM

Excellent!

2500 MHz is pretty good with 1.85vcore Barton is like a mobile! Amd even notice works to achieve its greater stability and CPU are made long ago. the new ones are able to achieve their 2400mhz or as happened to you with a Sempron 2600 + 1.85 Vcore achieve 2500mhz with a heat sink and is not as good for oc.

Good –

**Bob Willis** · 05-06-2009, 12:00 PM

I stop.... semprom a 2200 + do not work... stay well..... Also try the bridge in the socket.... Neither worked ... better buy me a mobile Barton 2400 +.... I give up my semprom ... So if my semprom currently 1800reales it's ... you just raised the fsb to 200 and it works ... and not heated almost anything.... hopefully get to the volcano with a 39 ° to 11 full.

**Adam Hollioake** · 05-06-2009, 12:03 PM

It is rare that either do not work with the kt600. What changes has this badge? I guess you did the mod on the L5 (2) and (3). A Sempron 2200 + should be easy to unlock 11x or 12X.