Make a good overclock my pc

**Jim Crow** · 05-11-2009, 08:26 AM

Hello everyone.

You have not been around here and I have lost a little training, I wonder if someone can help me make a good overclock my pc. Features are:

Processor:

Intel Core 2 Duo E6600
Code Name: Conroe
Technology: 65nm
2.4 GHz
Bus: 26.7
rated fsb: 1066.8
Multiplier: x9.0

Motherboard: ABIT IN9 32X MAX (C55XE-MCP55XE)

DDR2
4096 mb
Frequency: 400.0 MHZ
fsb: dram 2:3
CAS # latency: 5.0 clocks
RAS # to CAS # Delay 5 clocks
cycle time (after) 18 clocks
bank cycle time (TRC) 24 clocks
command rate (CR) 2T
voltage v 1.8

**John Emburey** · 05-11-2009, 08:27 AM

Hi.

Disputes, poster fabrics that come your Bios settings.

**Mike Gatting** · 05-11-2009, 08:28 AM

Friend ...
Bios screen to help you,
There is a section where you can alter the values (voltage, FSB, etc) and enable or disable things.
You can write or photos shoot
Hugs

**Norman Gifford** · 05-11-2009, 08:29 AM

Hi

I leave you here what I had requested.

Thank you for responding!

**David Gower** · 05-11-2009, 08:30 AM

Well ... trying to help!
But it is important to Know that if you overclock a perfect and refined "... the lower voltages be possible ... and I can not know this without having to test its stability and machine... pass configurations with a margin (a little over voltage ... so you do not cause instability)
Overclocking in "manual"
Multiplier 9
FSB 1380 (CPU clock = 3105) hair cooler box - if not this tempt fosse 3600 (depends on your individual capacity is processed)
= 690 MHz DDR2 (Unlinked use ... but you can use a 800 MHz or more memory you have is a good chip
CPU core 1.42 ~ 1.45V (start with 1.42 ... it is not possible to upload)
DDR2 voltage factory puts on your memory (I think 1.9V)
NB you put 1.58 <1.62> 1.65V
The other voltages for overclocking this light hold them
Maintain or "locked" CPU core or disable ... We have to be unlocked.

**Keith Fletcher** · 05-11-2009, 08:31 AM

Hi.

I'll see what happens and upload the results.

Thanks!

**Ian Botham** · 05-11-2009, 08:45 AM

Hi

I hope your results ...

It does not happen try to help.... good overclock.

**Jim Crow** · 05-11-2009, 08:47 AM

Hello, I have a small problem the default NB voltage is 1.35 and 1.40 are likely to increase, 1.45, 1.50 and 1.55 if you could help me via msn, I am at this time with a notebook next to my computer effect and thanks again.

**Bob Willis** · 05-11-2009, 08:48 AM

Hello

I do not have Skype you can call when it needs...

**Jim Crow** · 05-11-2009, 08:49 AM

Hello, your efforts to help this hard-head had their reward at the end by changing the BIOS version and I did the attachment you overclock results here and I would like to know, if you think your follow up or not.

**Geoffrey Boycott** · 05-11-2009, 08:50 AM

Hi

Spent the prime95 or orthos to see how the temperatures are in full?

**Jim Crow** · 05-11-2009, 08:50 AM

Apply orthos but the truth is not how long you have to let it be 2 minutes 9 seconds. And the result is 0 errors, 0 warnings running at 100% has a temperature of 52 degrees.

**Mike Brearley** · 05-11-2009, 08:51 AM

You know, the previous changes we had was very bad ...
This is better that you go ...
implemented a program called Prime95 (Small FFT) for 2 hours on your screen or Core Temp I think lower the voltage to 1.44 (approximately) ... lowered the temperature ...
This is the first step ... disputes others help us to improve the memory timings ... and rise ... this frequency ...