Thread: First Overclocking

Hi all.

I have done my first oc. My process is an E2180@2.00Ghz and I left 2.1 I would not climb over that did not have much faith in the source (Generic 600) until all stable now, but some have emerged problem

1.-When I open the CPU shows me good fsb (default 800) to 840 but it shows the multi x6 and x10 as not configured in the bios (sometimes it shows x10) I think this should be by the source that you are not delivering a stable voltage (I think, correct me if I'm wrong)

2.-speed memory down to 330.The temperature of the process without charge is 27, and 28 º Orthos stress rises to about 50 º (with the lid open cabinet, closed in the 52 or 53 degrees) temperatures taken by the everest.

Waiting for the font change to increase the FSB more. With the cooler that brings the process may reach 2.2 without having temperature problems?

My intention would be to leave it to 2.5 but with a 500W be achieved with these components you intend to buy (get to 2.5 stable) If you climb over the fsb will also further lower the speed of the memories?

Well hope to guide me a bit in my first oc unique because what I've done so far has been only raising fsb.

Greetings

Hi

The multiplier and the lower frequency when the CPU is not in use, it is normal ...

You can buy Hyper Tx2...

The lowering of the reports must be because the car got the bios, so the mother not to overload a low divider.

What the source does not see it as well, but good depends on the rest of your pc, mine is Generic 350W, and I have a 20% oc 24 / 7 without any problems, measured with a voltage tester to play and never came down, you would recommend this if you can, to deny the subject of your source. 50th is very good, is not high, the CPU about 70 degrees before you download multiplier, so you can go up more with the stock fan, so unusual that they have hot, mine is also stock, and the maximum is 45 º , I got it at 1200rpm all the time.

Also get a look at the "thermal ceramic" artic silver 5, at temperatures much help.
You have the job of governing the memos, and search the bios disable the Halt State, which is responsible for regulating the voltage when the cpu reduce your speed, you can cause instability in a larger c, the speed step or I leave, do not bother anyone, but if you're looking for disable spread spectrum.

What I said witch burner (burn the witch XD) is really low to the multi Core and 6 in the PDC, to relax the CPU, using the total msn or word you do not need the full force of the CPU. The speed is reduced as you said, but is due to the reduction of multi, FSB continues to not reduce the performance of the rest of the PC.

Then upload it to 2.2? Well as it is now or expect the best source and the topic of memories as I can raise the speed of adjusting the latency...?

Who are now at 5-5-5-15 or nothing to do? And in the cooler (the link I put up) but far fewer degrees lower temperature process with this cooler installed.

Greetings and thanks!

What's cooler is not what you know.
Check with everest or some other program (voltages 12v especially after playing or using any program that stress, so if you know what your source is providing adequate power and say that you c will be stable and safe for the pc.

The speed of reporting is separate from the latencies in the bios had to be two options, always. 5-5-5-15 is a bit high for 660; they may fall a little more.

Yes, if they are the two options but when I try to upload speed, for example try to upload it to 670 but the system does not start, as it restarts after 5 seconds of power without even being able to access bios so tube to remove the battery.

Temperature until this process can work without any risk? A full 65 ° is normal, right?
We want to get 2.5..... I can?

Greetings

Hi

Leave latencies outside SPD (auto) and high as possible, usually 6-6-6-18, so sure that will not bother you, then it should be able to upload 800MHz.

Hello again.... I stopped at 2.2 and it appears everything is fine, the temperature does not exceed 50 ° to full (according to Everest when he passed Orthos for 20 minutes) in the night I'm going to leave power with a 5 hours walk Orthos to see if the OC is stable.
I am interested in the subject of reports, if someone directs me to go up a little speed.

Greetings.

Hello

So do not hold the oc, raise voltages would be needed, which brings other problems and so it would be best in the 660 and let him look good by testing with orthos latencies.

To all this is that latency? That the role, what is the difference between who are 5-5-5-15 to 6-6-6-18 are.

Sorry for asking so much but I am very interested to learn

Greetings

You used to overclock from windows, so as you using the orthos, leave until you do not pull orthos error. So I do. if it starts to fall a lot and the voltage starts rising again overclocked.

I always do that.

Latencies are the time taken to respond to reports in certain actions, so if you are lower you get more performance but less oc, and if they are higher oc more but less performance.

The idea of D-LIRA is good, just need to find out the PLL from your mother and hope that in this clocked.

Hello again..... I stopped at 2.4 with Orthos running for 6 hours without any errors and the temperature never exceeds 50 ° but I think the cold night had helped a bit yesterday.... Finally, the thing is not throwing any errors, could you say that the OC is stable?

I am starting to enjoy this process, it was read out there that this process easier it could get without touching voltages 3.0 ... will this really true?

Oc to DDR2 at 2.1v minimum.

I draw the car on the first list and start searching by hand. 6 hours of orthos without faults is excellent, a very stable oc, I try to stay calm 1 single.

Hi

Go tested the stability of the oc with different latencies (lower).