Thread: Athlon X2 5200+

A couple of weeks ago I bought an Asus M2a-VM motherboard which has integrated video ATI x1250 with a micro Athlon x2 5200 + Brisbane 65nm core, DDR2 800 MHz memory super talent.

I did up the fsb, htt or in this case from 200 to 225 MHz, the multiplier in the maximum 13.5 allows the mother to me, getting a final frequency of 3037.5 MHz, the original 2700. The problem this brings is that he went to Link Ht 1124.3 MHz, and I understand that this value should never exceed 1000 MHz, and the memo went to a little over 800 MHz to 867 MHz to be exact. Realize the stability test with me and ORTHOS error in the draft memo, the system is unstable. I understand that this drawback is solved by lowering the Link Ht in less than 5 which is the default value, but the mother did not give me that option, I can only handle voltages, and the htt multiplier.

One observation is that when running the application that brings the Mother of ASUS, says that the maximum frequency that supports my micro is 3800 MHz. I can really get that clock? Another issue is that the overclock Ati x1250, download Atitool 2.6 but I may not overclocked memory, which is understandable, and not the gpu, and in so doing automatically, takes a long time and not get anything, and if the change value manually, then go back to the original value.

Hello, I have the same board but with a x2 4000 + I could ocear smoothly even with the core Atitool. Now I'm going out to classes in the afternoon to see if you could help a little.... by the way with the latest bios (1604 (beta)) everything is unlocked, but it is useless to lower the multi, it is not fishing XD That.

Well, I hope your help! I need to clarify that I have 1 GB of ram and the bios will update yesterday to the 1604 beta, but I saw no option extra. Now I'm going to check.

Thank you very much!

Hello, reading your 1st post I have to say is no greater problem (is always stable) is the htt link on 1000, I have come to a stop more than 1300 totally stable (Ht Link 600 comes in the form 800 1000 (states would be 5X200 is the stock value), the other the memos could be limiting you, mine did the run to just over 900MHz, so if memos down the left foot just to 800MHz I was unstable and he threw me the errors in orthos XD.

I use the Atitool 0.26 climb and reach the core of 400 to 500, obviously you can not touch the memories, it is rare to tighten “set clock" values change to some very low, but do not be scared, and to revise Everest in or Ati catalyst control center is the change, and there is not much good at actually winning a few more points in 3dmark ....

That good friend, I hope you told you will serve as. Now walk a bit rushed, I hope someone more experts on the subject can help.

Greetings

I have the same board with the same procedure and some very ordinary memories, gender, and brought him stable and 3250, (that if someone got more in this topic sure to draw much more), in winter and a fountain with a little more powerful I think get more.

As a reference test, with voltages of 1425 and 250 x 13, I got to 1300 and not a stability problem, and gives me more performance.

I forgot to say that the Orthos always gives me problems, but I leave the computer whole day, heat and everything and never restarted, not fish before had the same question with Atitool.

Greetings

I must inform you, as I explained that I set my cpu, which is not entirely stable, surfing the Internet because I was suddenly hangs the explorer, I pulled an error should be closed. With no other problem, or playing audio, video or any game, except ORTHOS, which gives me error? I will try to pass as you say, dropping the 0.5 multi, leaving at 13 and raising the HTT to 250, but I suppose to raise the base HTT clock and the memos, what worries me. I will raise the Vcore default is in the EVEREST 1.376vy says that the range of the micro goes to 1100 if 1400 is not to cheer. The memos are working down to 1.8 seconds Everest, climbing may be a little stability to see if I win? With respect to ATITOOL , if you give me a hand to set you, as it happens, are placed very low value, but what is the correct value should I give? Because when you open the program I get the frequency. The GPU at 57.28 MHz and 400.96 MHz in the memo, when in reality they are working on 400 and 200 respectively? I will let you know that I got into settings and select the option to USE DEVICE 0x791E that version 0.27 is the only option that appears. At 0.26 exactly the same thing happens.

I await your responses and thank you very much now.

I will prove what I said and I tell them.

Thank you.

Hello, I believe, should say 400.96 in both.... what can change is the core and upload it to your whim and under your responsibility (I climbed to 500) and then click on Save and then Set Clock and closes it (even if you change to the previous value), then check in Everest or in the catalyst and hence will change

Greetings

A problem with the voltages, do not be discouraged, if not, to the 1425 draft, and only rises a temperature, is ugly memory ordinary (imagine to buy Luke 12) he shot me 2.1vy function as a 820 I think, I do not remember well, of 667 stock.

Greetings.

Good so long. Make a couple of tests, it increased the Vcore but remains unstable, perhaps due to the htt that exceed 1150. I would like to know if anyone can help lower the LDT (multiplier of the internal bus of the micro default 5) to multiply that by the ht have to give less than 1000. I understand that an overclock would be more effective in achieving the lowest value and increased leverage of ht, therefore I have to lower the LDT (my mother is an ASUS M2A-VM with the latest version of the bios) and my mother I do not permits.

Many thank you very much.

Suddenly the stability of the raise coming through a little voltage, the memos also if you go low frequency q wadding into the configuration of the plate, so you are not the MHz both shoot and could benefit a greater oc course ht is a 4-down bring to more oc filly also ELN I understand it may NOT ocear instead when the upload process reports already up the memos, so Atitool does not help in the case of integrated.