Thread: AMD Athlon XP 2800+ processor

This is my team:
Processor: AMD Athlon XP 2800 + (2083) AXDA2800DKV4D 9788587280425
AQUCA0404MPMW 1999AMD
Memory: 1x512MB Kingston Value DDR400 PC3200
Chips KVR400X64C3A/512
License plate: ABIT AN7
HDD: 2x120GB Maxtor SATA

The chip is 333Mhz, and memory board can go to 400Mhz. As I understand the micro and it is blocked but I uploaded the FSB is 170.

I am looking to buy a kit d memories (2x512 or 2x1024) and puts them in DC, I guess I will have to set more on the chips that the trademark / models, one knows that someone shot a fixed bring TCCD or BH-5?

You are going any better or how to improve it?

I hope not too many questions and some charitable soul will respond!

I am good almost the same PC is just what my process is a mobile 2500 +. My process is going to 2100MHz (210x10) with 1.5vpara not very hot so my memories are at 220MHz with the stock 1.9v with 3-3-3-11 (if it is with heat sinks), besides the North Bridge this to 1.7v for stability. This I tell you that the pieces should be similar to a result equal or superior.

As the procedure is fine, I believe that no problem should be overcome with a 2100MHz configuration 210x10, but that if a little more voltage, which should be no problem with the volcano. The reports should give more of 220MHz with latencies acceptable. If not could you could try a BIOS overclockers more.

Be careful with the temperature and whether to change bios sure to do it with your PC without overclock and with absolute certainty that the BIOS is correct.

Thanks for responding! If they are almost equal to your pc! I do not have the luck to have but what I say and I read in the forums upload my XP 2800 200 MHz (which is my goal) locked with the clock at 12.5.

Regarding the reports... someone knows any brand / model to bring the draft fixed chips TCCD or BH-5? It’s my gift kings and yet I have not asked.

Well, it is likely that the CPU went bad, or maybe you have not activated the PCI lock. And another thing, its dual channel, as in socket not much, if you see Sandra, I think the 2005 has a memory test of an nforce2, and notice that between single channel and dual channel, the difference is minima. Although it is certainly good to have more RAM.

This process of selling the country to buy a mobile because it's a good idea before I had a 2000 + by Tb you got 2000Mhz + or - almost 1.9vy but now I have a Mobile 2100MHz but it's at 1.5v, and it no upload not have to be increased rpm of the volcano and also send off the FAN dl cabinet maintained at 55 º to 34 º full that made the other day in Santiago.

First thank everyone for responding! What I am going to do is catch the kit and then the micro memory. I am undecided between these kits:

OCZP4002GK
OCZ4002048ELDCPE-K
OCZSOE4002GK

TWINX2048-3200C2
TWINX2048-3200C2PRO
TWINX2048-3200LLPRO

PDC263200LLK

ADBGC1A16K

Any suggestions? Do you know if any of these mounts TCCD? I guess if you have to look at both sides, or one ... I got more complicated, but it sure is that I sent him…

I would go for TwinX C2PRO probably bring TCCD, and although it was not so I do not think you disappointed in the OC.

If they come with chips on 2 sides no problem, you want a BIOS with CPC and walk of wonders.

Greetings!

A tip for you is tell him to go and buy some TCCD to 2T

Only thing is that you have right to use one side only memories to go as God 1T

The ideal combination for the nForce2 is a Ch5/Bh5/Bh6 and some revisions to a single-sided (The downside is that it will be 2x256)

To get the most out of this chipset, will go over 245/250Fsb at 2-2-2-11 1T

1T some TCCD to go ass with this chipset, and strange to me that people Council this combination.